google AI: Is there a way to balance the voltages in a prallel array of PV panels

 

google AI: Is there a way to balance the voltages in a prallel array of PV panels

Yes, you can balance and manage mismatched voltages in parallel solar panel arrays. Left unmanaged, parallel panels force the entire array to drop to the voltage of the lowest panel, which severely limits your total power output. [1, 2, 3, 4]  

Here are the most effective ways to balance voltages and maximize your yield: 

1. Use DC-to-DC Optimizers (Best Solution) 

Installing smart module-level optimizers (like those from  Tigo Energy 

 or  SolarEdge 

 on each panel conditions the voltage of individual panels before they combine. This allows every panel to operate at its maximum power point (MPP) independently, completely eliminating the voltage penalty. 

2. Independent Charge Controllers 

If your panels have vastly different voltages (e.g., mixing a 12V panel with a 24V panel), the best approach is to wire them into separate, dedicated charge controllers. Route each panel or string to its own  MPPT Charge Controller 

 before connecting them to the battery bank. 

3. String Inverters with Multi-MPPTs 

If you are using a grid-tied string inverter, look for a model that features multiple Maximum Power Point Trackers (MPPTs). You can wire your mismatched strings to separate tracker inputs, allowing the inverter to individually balance and optimize the voltage for each parallel group. [10, 12, 13, 14]  

4. Direct Diode Protection (Emergency Use Only) 

In a pinch, if you have two panels with similar but slightly mismatched voltages, you can use blocking diodes (or Schottky diodes) on the positive lines. This prevents the higher-voltage panel from "dumping" current into the lower-voltage panel. Keep in mind that this is not recommended for permanent setups, as the lower-voltage panel will still fail to produce its maximum potential power. [12, 15]  

Rules of Thumb for Parallel Arrays 

• Keep them close: If you must wire panels directly together in parallel, ensure their $V_{mp}$ (Voltage at Maximum Power) ratings are within $0.5\text{ to }1.0\text{ Volts}$ of each other. 

• Match series strings: If you are building parallel strings (multiple panels wired in series, and then paralleled together), ensure every single string is identical in both panel count and model type. [11, 13, 16, 17]  

AI responses may include mistakes.

[1] https://www.reddit.com/r/SolarDIY/comments/1dqtao7/can_i_connect_different_voltage_solar_panels_in/

[2] https://community.goodsam.com/discussions/technicalissues/series-parallel-configurations-for-solar-panels/3561082

[3] https://www.facebook.com/groups/447643471600275/posts/682772848087335/

[4] https://xantrex.com/about-xantrex/blog/marine/understanding-the-impact-of-series-parallel-and-mixed-solar-wiring-on-system-efficiency/

[5] https://diysolarforum.com/threads/unbalanced-pv-in-series.64527/

[6] https://diysolarforum.com/threads/can-shading-be-dealt-with-by-parallel-strings.54317/

[7] https://solarpowernation.com.au/power-optimizers-explained-enhancing-solar-system-performance/

[8] https://www.linkedin.com/pulse/how-fix-voltage-mismatch-solar-pv-systems-causes-solutions-barua-jtkuf

[9] https://www.anernstore.com/blogs/diy-solar-guides/rapid-shutdown-strings-microinverters-optimizers

[10] https://diysolarforum.com/threads/volts-series-amps-parallel.10654/

[11] https://diysolarforum.com/threads/solar-panels-with-different-voltage.75463/

[12] https://www.youtube.com/watch?v=OnV8UYBqzD4

[13] https://www.youtube.com/watch?v=b2H8vpj8rQg

[14] https://www.facebook.com/MultiTechInfoo/posts/when-connecting-multiple-strings-in-parallelvoltage-must-match-closelyif-one-str/1408124434688499/

[15] https://diysolarforum.com/threads/how-do-i-match-solar-panels-of-different-wattages-in-a-parallel-array.6581/

[16] https://solartechonline.com/blog/how-to-wire-solar-panels-in-parallel/

[17] https://www.facebook.com/groups/2573968699280898/posts/8156362984374747/

Inverter replaced plus more

 

The most recently purchased inverter that seemed to have random overnight shutdowns was returned.

Instead, I paid  little more and got a newer version that has been installed and running without event for over a week.

I ordered and received fifteen Staubli MC4 connector pairs. Staubli is the original designer and manufacturer of MC4 connectors. This will, I hope, resolve any intermittent connection errors due to cheap, marginally standardized, connectors.

Another improvement is the addition of fifty feet, each, of red and black #8 AWG cable that will reduce any line losses due to existing #10 AWG cables running to the array from the house. 

A hand crimper, for smaller gauges, and a hammer crimper, for #8 AWG and larger sizes, have been added to my tool set.

A series disconnect switch has been placed in the PV array-to-charge controller circuit. A series 40A fuse has yet to be installed in the charge controller-to-batteries circuit.

A second Epever Triron charge controller was purchased as a replacement/backup for the existing unit. For a while, random fluctuation in csv recorded data occurred in the first 30-45 minutes of operation, in the mornings. I reset the start time to 6:30AM and the fluctuations have stopped. The repair mentioned previously, seems to be holding up.

After some calculations and some thought, and a consultation with Epever, I came to the conclusion the reason my system was not charging at a full 1KW was the batteries are in parallel. If I wire them in series-parallel with a resulting voltage oof 24VDC, instead of 12VDC, the controller will increase the rate of charge. for the inverter input, at a maximum current of 170A.

However, I would have to use an inverter that takes a 24VDC input and mine are rated for 12VDC. The 24VDC verison of my inverter, Xantrex Freedom X 1200W/2000W, is hard to find, especially on ebay, and is very expensive.

I could add a 'buck', or step-down, converter, but they are expensive. The converter would convert 24VDC to 12VDC

For the time being, I'll settle for a 600W maximum charge rate.

Used Xantrex inverter potential problems

 There have been a couple of instances where the inverter may be failing or creating anomalies.

I'm gettinga new RPi4 and using an SD card to eliminate the existing RPi4+SSD as a source of problems.

A new inverter may be needed. The csv files are not recording as usual.

A long standing problem solved

 

For a long time, The graph display was not reflecting the change to Daylight Savings Tme.

The solution lay in editing the php.ini file to set the date.timezone to "America/New_York".

The setting in the EpD3Dy.php file was commented out.

The display is now correct when the spring/autumn changes occurs.

However, the graphing now ends at 7PM instead of 6PM. A minor edit will correct that error.

Spring forward-Fall back